Dryer Error Codes

Dryer
Display	Description	Cause/Corrective Action
Alrn, ALrn or ALArn	Break-in Alarm Error	Service the service door or coin vault switches.
door	Door Open Indicator	Door is not closed during an active cycle. If door is closed, check for improper wiring or inoperative door switches.
E rr or Err	Coin Error	Invalid coin pulse or inoperative coin sensor. Check coin drop area and remove obstructions. If error persists, tampering may have occurred. Evaluate security procedures.
E:00	General Error	Re-aim external device and try again.
E:01	Proximity Error	External device is improperly aimed at infrared communicator (angle or distance). Re-aim external device and try again.
E:02	IR Communication Disconnection	External device removed before communication complete. Re-aim external device and try again.
E:05	Invalid Value Communication	Invalid code downloaded from external device to Electronic Control. Before downloading, ensure data is for current machine type.
E:07	Inoperative Control	Replace control.
E:08	Inoperative Control	Replace control.
E:09	Proximity Error	External device is improperly aimed at infrared communicator (angle or distance). Re-aim external device and try again.
E:0A	Proximity Error	External device is improperly aimed at infrared communicator (angle or distance). Re-aim external device and try again.
E:0B	IR Communication Disconnection	External device removed before communication complete. Re-aim external device and try again.
E:0C	IR Communication Disconnection	External device removed before communication complete. Re-aim external device and try again.
E:0F	IR Communicator Programmed Off	Reprogram infrared communicator on. Manually enable IR on control/Re-aim external device and try again.
E:OP	Open Temperature Sensor Error	Open temperature sensor circuit wiring. Change sensor.
E:SH	Shorted Temperature Sensor Error	Short in temperature sensor circuit wiring. Change sensor.
EC:00	General Communication Error	Communication failure. Try card again.
EC:02 or EC02	Timeout Error	Communication failure. Try card again.
EC:03 or EC03	Invalid Command Code	Communication successful, but the command was not valid for this machine type, or the control could not perform the command in its current mode of operation. Before downloading, ensure data is for current machine type and control is in correct mode.
EC:05 or EC05	Invalid or Out-of-Range Data	Incorrect machine type or the value in at least one of the programming options is invalid or out of range. Before downloading, ensure data is for current machine type and recheck the programming option's value and try again.
EC:06	Invalid Data Code	Incorrect machine type. Before downloading, ensure data is for current machine type.
EC:09	Corrupted Data Error	Communication error. Try card again.

Dryer
Display	Description	Cause/Corrective Action
EC:0A	Invalid Machine Type	Incorrect machine type. Before downloading, ensure data is for current machine type.
EC:19 or EC19	No Card Reader Communication	Communication failure. Check card reader, control and harness. Power down, power up and try again. If error persists, replace control or card reader.
EC:20	Unreadable Card	Inoperative card/ dirty contact. Clean chip on card or card reader contacts. Try card again. If error persists, card may be inoperative.
EC:21	Security ID Mismatch	Wrong card. Use card with correct security code.
EC:22	Site Code Mismatch	Wrong card. Use card with correct site code.
EC:23	Card Maximum Value Exceeded	Value on card over max. Use a card which does not exceed maximum value.
EC:24	Insufficient Memory on Card	Card memory is full. Download card contents to PC and clear card for re-use.
EC:25	Card Reader Malfunction	Inoperative Card Reader. Card Reader may need to be replaced.
EC:26	Card Write Error	Try card again. If error persists, card may be inoperative.
EC:27	Diagnostic Test Card Write Failure	Inoperative Card Reader. Card Reader may need to be replaced.
EC:28	Diagnostic Test Card Read Failure	Inoperative Card Reader. Card Reader may need to be replaced.
EC:29	Diagnostic Test Memory Test Failure	Inoperative Card Reader. Card Reader may need to be replaced.
EC:2A	Diagnostic Test Card Interface Failure	Inoperative Card Reader. Card Reader may need to be replaced.
EC:2b	Diagnostic Test Flash Checksum Failure	Inoperative Card Reader. Card Reader may need to be replaced.
EC:2C	Biberon or Non-biberon Device Failure	Faulty card reader. Replace card reader.
EC:2d	Firmware Update Failed, S/W (Software) Intact	Firmware load failed. Replace card reader.
EC:2E	Firmware Update Failed, S/W Not Intact	Faulty firmware in reader. Replace card reader
EC:2F	Firmware Updated, S/W Not Intact	Faulty firmware in reader. Replace card reader.

Dryer
Display	Description	Cause/Corrective Action
EC:30	Timeout Error	Card Reader may need to be replaced
EC:31	Hotlisted Card Inserted Into Reader	Card hotlisted. Control will destroy card.
EC:50	Loyalty Purse Read Error	Try card again. If error persists, card may be inoperative.
EC:56	Loyalty Purse Write Error	Try card again. If error persists, card may be inoperative.
EC11	No Card Reader Initialization	Communication is valid, but there is no card reader initialization. Power down, power up and try again.
EC18	No Communication	Card reader initialized, communication lost. Power down, power up and try again. If error persists, replace control or card reader.
EC36	Audit Card Removed Prematurely	Re-insert audit card and wait until machine prompts for card removal.
EI:00	General Communications Errors	Communication failure. Re-aim external device and try again.
EI:01 or EI01	Transmission Failure	Communication failure. Re-aim external device and try again.
EI:02 or EI02	Device Timeout/Timeout Error	Communication failure. Re-aim external device and try again.
EI:03 or EI03	Invalid Command Code	Communication successful, but the command was not valid for this machine type, or the control could not perform the command in its current mode of operation. Ensure data is for current machine type and control is in correct mode.
EI:04 or EI04	Expecting Upload Request or Command Packet Time Out	Communication failure. Re-aim external device and try again.
EI:05 or EI05	Invalid or Out-of-Range Data	Incorrect machine type or the value in at least one of the programming options is invalid or out of range. Before downloading, ensure data is for current machine type, values entered are within the minimum and maximum limits and recheck the programming option's value and try again.
EI:06	Invalid Data Code	Incorrect machine type. Before downloading, ensure data is for current machine type.
EI:07	Error Writing to RTC	Control failure. Control may need to be replaced.
EI:08	Error Writing to EPROM	Control failure. Control may need to be replaced.

Dryer
Display	Description	Cause/Corrective Action
EI:09 or EI09	CRC-16 Error	Communication failure. Re-aim external device and try again.
EI:0A	Invalid Machine Type	Incorrect machine type. Before downloading, ensure data is for current machine type.
EI:0F or EI0F	Invalid Wakeup or IR Disabled	Communication failure or IR is disabled. Manually enable IR on control/Re-aim external device and try again.
EI0A	Framing Error	Communication error. Re-aim external device and try again.
EI0C	Time-out Exceeded	Communication error. Re-aim external device and try again.
EI0E	Encryption Error	Incorrect machine type. Before downloading, ensure data is for current machine type and check security code and retry.
EoP or E oP	Open Thermistor Error	Remove any lint build-up around thermistor. If problem persists, replace control or thermistor.
ESH or E SH	Shorted Thermistor Error	Remove any lint build-up around thermistor. If problem persists, replace control or thermistor.
E id	Board ID	Incorrect replacement control. Replace user control or output board with correct part.
E dS	Brownout/Voltage Configuration	Unexpected supply voltage. Check the harness connections between the user control and the output board. If the user control was replaced, set dipswitch #1 to the same setting as the previous control. If reworking the machine to use a different supply voltage, the dip switch #1 setting may need to be changed. If the dip switch #1 setting is changed, power down, power up and try again.
E nr	Output Board Not Ready	Hardware failure. Replace output board.
E bS	Output Board Communication	Hardware failure. Replace output board.
EnXX	Machine ID	Communication failure. Power down, power up and try again. If error persists, check connection between user control and Machine ID chip, or try replacing the user control or the Machine ID chip.

Dryer
Display	Description	Cause/Corrective Action
E Co	Output Board Communication	Communication failure. Power down, power up and try again. If error persists, check connection between user control and output board, or try replacing the user control or the output board.
E 59	Door Input Acquisition	Hardware failure. Replace output board.
E 60	Centrifugal Switch Input Acquisition	Hardware failure. Replace output board.
E 61	High Limit Thermostat Input Acquisition	Hardware failure. Replace output board.
E ro	Locked Rotor	The motor is not sensed as rotating when it should be. Check that nothing is obstructing motor rotation, check connection between user control and output board, or try replacing the user control or the output board.
E nS	Motor Output Shorted	Hardware failure. Replace output board.
IN USE LED blinks three times + 1.5 second pause	Shorted Thermistor Error	If the control sense a temperature greater than 210±4°F during an active cycle it will set a Shorted Thermistor error. The control will flash the IN USE LED three times separated by a one and a half second pause. This sequence is repeated as long as the Shorted thermistor error is sensed.
IN USE LED blinks twice + 1.5 second pause	Open Thermistor Error	If the control sense a temperature less than 0°F when the heat has been on for at least three minutes it will set an open thermistor error. The control will flash the IN USE LED twice separated by a one and a half second pause. This sequence is repeated as long as the Open Thermistor error is sensed.
OFF or oFF	Break-in Alarm Shutdown Error	Service the service door or coin vault switches.
OP	Open Thermistor Error	Physical open in the thermistor circuit. Replace thermistor. Possible causes are: 1) thermistor, 2) wiring between control and thermistor or 3) control.
Right most DP (decimal point) Lit	Network Communication Error	Communication failure. Wait for 1.5 minutes for error to clear. If it doesn’t, power-down and power-up the machine. If error persists, control or Network Board may need to be replaced.
SH	Shorted Thermistor Error	Dead short int he thermistor circuit. Replace thermistor. Possible causes are: 1) shorted thermistor, 2) a short in the wiring between control and thermistor or 3) control.